Design of Combined Footing
This article provides an overview of the design of combined footing. At the end of the article, a practical worked example is presented on the design of combined...
Tag: Worked Example to Eurocode 2
Design of Pile cap using Bending theory – Worked Example
This article presents a worked example on the design of a pile cap using bending theory. The pile cap shall be proportioned, designed for bending, vertical shear, as...
Design of PSC Beam for Shear Strength – Worked Example
This article presents a worked example on evaluating the shear strength of a prestressed concrete (PSC) beam using EN 1992-1-1-2004. The beam shown below is an I beam...
Pile Cap Design using Strut-and-tie Method – Worked Example
This article presents a worked example on the design of a pile cap to EN 1992-1-1-2004 (Eurocode 2). The pile cap to be designed is to transmit column...
Design of Planar Shear Walls – Worked Example
This article presents a worked example on the design of shear wall to EN 1992-1-1-2004 (Eurocode 2). The shear walls to be designed form the major stabilizing system...
Design of Prestressed Concrete Beam for Flexural Capacity – Worked Example
This article presents a worked example on evaluating the bending capacity of a prestressed concrete beam. After verifying the stresses within a prestressed beam is within limit, it...
Design of Eccentrically Loaded Pad Foundation – Worked Example
This article presents a worked example on the structural design of pad foundation subjected to axial load and moment to EN 1992 -1-1-2004. The geotechnical aspects of the...
Design of Axially loaded Pad Foundation – Worked Example
This article presents a worked example on the structural design of axially loaded pad foundation to EN 1992 -1-1-2004. The geotechnical aspects of the design shall be approached...
Comparative Analysis of flat Slab between MCM and EFM – Worked Example
This article presents a comparative analysis between analysis of flat slab using moment coefficients method (MCM) in table 3.12 of BS 8110 and equivalent frame method (EFM). Moment...
Design for punching Shear – Worked Example
This article presents a worked example on the design of punching shear for flat slabs to BS EN 1992-1-1-2004 (Eurocode 2). The flat slab to be designed for...
Design of Flat Slab – Worked Example
This article presents a worked example on the design of flat slab to EN 1992-1-1-2004. The plan of the flat slab to be designed is shown below. It...
Flat Slab Analysis using Equivalent Frame Method – Worked Example
This article presents a thorough worked example on the analysis of flat slab using equivalent frame method. At the end of the article, the analysis of the equivalent...
Design of continuous one-way spanning RC slab – Worked Example
This article presents a worked example on the analysis and design of continuous one-way reinforced concrete slab. The bending moments and shear forces are obtained using tabular coefficients...
Constructing Magnel Diagram for prestressed Concrete beam – Worked Example
This article presents a worked example on the construction of magnel diagram for the design of a prestressed beam section. The beam that shall be designed is the...
Verification of Stress in a Prestressed Beam – Worked Example
This article shows a practical worked example on how to check the stress in a prestressed concrete beam using the combined stress approach. Verifying the stress will enable...
Design of Half-turn Staircase to Eurocode 2 – Worked Example
This article presents a worked example on the design of half-turn staircase to Eurocode 2. The staircase to be designed connects the ground floor and the first floor...
Design of Slender Column to Eurocode 2 – Worked Example
A slender column is a column that is vulnerable to buckling which prevents it from harnessing its maximum strength. Several codes of practice have devised diverse methods to...
Design of Column to Eurocode 2 using Design Chart – worked example
Column design charts are created to simplify the design of reinforced concrete columns. These charts are suitable for columns with symmetrical arrangement of reinforcement and they are produced...
Design of Reinforced Concrete Flange Beam to Eurocode 2 – Worked Example
This article presents a worked example on the design of reinforced concrete flange beam to EC2.
Design of a Doubly Reinforced Beam to Eurocode 2 – Worked Example
This article presents a worked example on the design of doubly reinforced beam to EC2
Design of a Singly Reinforced Beam to Eurocode 2 – Worked Example
This article presents a worked example of the design of singly reinforced concrete beam to EC2. The image below shows the Plan view of a reinforced concrete structure,...